The components of the watch movement are very compact and the parts are very exquisite, therefore, the good or bad protection of the watch has a direct impact on the accuracy of the timekeeping and the length of service life. The general knowledge of using and protecting the watch is:
Buy watches at goodluckwatch.com, affordable prices and superior quality!
(1) to often use a relatively soft cloth or silk gently wipe off the case on the dirt and sweat rout, to maintain the appearance of the light clean. Do not open the case back cover.
(2) winding to have a fixed time, the best once on is. Full winding, walking time is accurate. Will not cause the clockwork break or reduce the service life. In the clockwork on the full, do not screw again vigorously to prevent damage to the mechanism. New with the clockwork, in just a few days, do not put the clockwork on the full, after a few days of use, the clockwork of the Xiequ gradually deepen can be on the full.
On the article, it is best to turn the tree shaft in one direction.
After using the hand attack for a long time, if the sense of the upper strip is too changed. You can add some silicone oil on the handle gasket to increase lubrication.
Automatic watch, when you take it down before going to bed, you should wind it up a few times to make it go up enough.
(3) When checking the time, the hand can be dialed by pulling out the shaft of the stem, and it can be dialed in either direction. However, calendar watches and aviation watches should not be dialed backwards.
(4) Do not allow the watch to get cold or hot, as a drastic change in temperature will increase the timekeeping error of the watch. Don't put the watch under the sunlight exposure or put it in the ice and snow with very low temperature, and don't put it in the very hot oven, because the high temperature will make the parts damaged or deteriorated, and the metal parts inside the watch will expand and contract, which will cause the timekeeping inaccuracy. Therefore, people who work in high or low temperature should remove the watch and put it in a heat insulated (cold) place when working. In storage, transportation and custody, it should be protected from sunlight and humidity, ventilated and dry. It is better to use the temperature at 0~35℃.
(5) Violent vibration should be avoided.
(6) Should avoid water immersion and moisture, the watch should be removed when washing. Is the water or swimming watch, in use for a period of time, due to the daily on the strip will also make the tree head like rubber gasket wear and tear, lose the effectiveness of waterproof. Moisture invades the watch, if it can not be dispersed in time, it will condense on the inner surface of the glass as a fog or a small show bead, severe: the heaviest leads to the deterioration of the dial, the parts of the rust, once you find that there is a fog, it should be wiped off in time.
(7) When a watch is magnetized, the accuracy of timekeeping will be affected and the magnetism will not be easily removed. Therefore, do not wear the watch to the strong magnetic field nearby. The watch is magnetized to make the watch go time error, and must be demagnetized.
(8) Can not put the watch and cosmetics such as powder in the same drawer or box, because the powder can be invisible from the naked eye gap into the watch machine pollution oil, affecting the operation of the machine parts. Especially, it should be noted that the watch should not be placed in a camphor closet, because the camphor will diffuse into the case after vaporization, which will make the oil in the parts solidify, lose the rust prevention and lubrication effect, make the parts easy to rust and wear, and cause the watch not to be allowed to keep time and reduce the service life.
(9) The watch is always in motion, so even if the watch moves normally, it still needs to be inspected and disassembled for cleaning and refueling on a regular basis, and should be disassembled and cleaned once every three years or so, and the time of disassembling and cleaning should be shorter if the sealing of the watch is worse, so as to lubricate the motion part, minimize friction and prolong the service life.
(10) When the watch is fast or slow, try to adjust the handle, you will have the experience to adjust the time. If the watch becomes slower than one day, then adjust the fast and slow needle is not effective, in this case, is the need to clean and refuel.
(11) Watches to be stored for a long period of time should be stored after cleaning and refueling. It should also be wound 1~2 times a month to keep the watch running well.